3M
3M™ Ceramic Microspheres
A 3M family of solid engineered ceramic particles, not interchangeable with hollow glass or hollow ceramic microspheres.
3M™ Glass Bubbles
A 3M family of thin-walled, hollow soda-lime-borosilicate glass particles; performance depends on the identified grade and application.
A
Abrasion resistance (also known as: wear resistance when specified)
Ability to withstand material removal from repeated rubbing or abrasion under a defined test and loading.
Accelerated weathering
Controlled laboratory exposure intended to reveal responses to selected stresses faster than natural exposure; not a direct field-life prediction.
Acid extraction
An analytical preparation in which a specified acid solution mobilizes selected constituents from a sample for subsequent determination; the result depends on method conditions and must not automatically be called total composition or environmental leachability.
Adhesion (also known as: interfacial attachment)
Resistance of a coating or adhesive layer to separation from its substrate under a specified test or service condition.
Adhesion promoter
A substance introduced into a formulation or applied to a surface to improve bonding across an interface. Its effectiveness depends on the substrate, binder chemistry and treatment conditions; it is not synonymous with every compatibilizer or proof of adequate adhesion.
Adhesive failure (also known as: interfacial failure)
Separation along an interface between different layers or materials, as distinct from fracture within a layer.
Advancing contact angle (also known as: advancing wetting angle)
The contact angle associated with a liquid advancing over a solid surface, measured at the onset of advance or during controlled spreading according to the stated method. Report the liquid, surface condition and measurement procedure.
Air temperature
The temperature of the surrounding air at the stated measurement location and time. It must be distinguished from substrate or specimen temperature, especially when interpreting curing, viscosity or condensation conditions.
Air-release agent (also known as: entrained-air release additive)
Additive facilitating migration or loss of gas bubbles within a wet coating film, distinct from the removal of foam already at its surface.
Air-void analysis
Microscopic characterization of the void system in hardened concrete, commonly using linear-traverse or point-count measurements on a prepared section. It can estimate air content, specific surface and spacing parameters. Features counted as voids must be correctly identified, especially when hollow particles are present.
Air-void chord (also known as: chord length)
The length of an intercept across an air void along a specified measurement line on a prepared concrete section. Average chord length is the total measured void-intercept length divided by the number of intercepted voids; it is not automatically the diameter of each void.
Air-void spacing factor (also known as: Powers spacing factor)
A calculated length parameter representing the spacing of an idealized air-void system in cement paste, derived from measured air content and void-surface information. It is a model-based indicator, not a direct measurement of every actual distance between voids or a guarantee of freeze–thaw durability.
Airless spraying
Application method that atomizes a coating or compatible filler through a spray tip using liquid pressure rather than atomizing air. Equipment, tip, hose and formulation define the tested process window; a successful spray does not prove hollow-particle survival.
Alkali-swellable emulsion thickener (also known as: ASE; alkali-soluble emulsion)
A pH-responsive acrylic thickener that swells or becomes soluble after neutralization and raises aqueous formulation viscosity.
Aluminosilicate (also known as: alumino-silicate)
An inorganic material containing aluminium-, silicon- and oxygen-based structural components; the term alone does not define a specific phase.
Anisotropy (also known as: directional dependence of properties)
Dependence of a measured material property on direction, which must be recorded for oriented or layered composites.
Apparent lap-shear strength (also known as: single-lap apparent shear strength)
Failure force divided by bonded overlap area in a defined single-lap specimen; not an automatic design-allowable stress for another structural joint.
Application viscosity window
The interval during which a mixed material remains within a defined viscosity range under a specified measurement protocol and intended application. Its duration depends on the chosen limit, temperature and sample history; it is not itself a measurement of reaction rate.
ATR-FTIR spectroscopy (also known as: attenuated total reflectance Fourier-transform infrared spectroscopy; ATR-FTIR)
Infrared analysis using the evanescent field of an internally reflecting crystal to probe near-surface chemical bands; not proof of through-film cure.
B
Back ionization
Electrical discharge associated with excessive charge accumulation in a deposited powder layer, which can disturb deposition and surface appearance. It is distinct from poor cavity coverage due to other causes and requires equipment-specific diagnosis.
Barrier effect
Resistance to transport through a material or coating that can delay the passage of substances such as water or corrosive species. A proposed packing benefit is not a measured barrier improvement without a relevant transport comparison.
Binder (also known as: film-forming binder)
The component that forms or maintains the continuous phase holding pigments and fillers together in the finished coating or composite.
Blocking resistance (also known as: paint blocking resistance)
Ability of a dried coating to resist undesirable sticking to another coated face under specified pressure, temperature, humidity and contact time; distinct from initial film formation or abrasion resistance.
Boil-off rate (also known as: boiloff; cryogenic boil-off)
The rate at which stored cryogenic liquid vaporizes, typically because of heat input, expressed per unit time for stated tank, pressure and operating conditions.
Bond-line thickness
Thickness of the adhesive layer between bonded surfaces. It forms part of the joint geometry and must be distinguished from bulk adhesive-specimen thickness and from an unfilled interface gap.
Bulk molding compound (also known as: BMC)
A prepared bulk-form mixture of resin, reinforcement, fillers and other ingredients for molding. BMC may be injection- or compression-molded; a result for sheet molding compound does not establish the behavior of a BMC formulation.
Buoyancy (also known as: upthrust; buoyant force)
The upward force exerted by a surrounding fluid on an immersed body, equal to the weight of displaced fluid under hydrostatic conditions. Whether the body rises, sinks or remains suspended also depends on its weight and other forces.
Burnish resistance (also known as: burnishing resistance)
Resistance of a low-gloss surface to visible local gloss change after polishing or rubbing.
C
Calcium carbonate (also known as: CaCO3)
The calcium salt of carbonic acid, with formula CaCO3. It occurs in several natural mineral forms and is used in particulate products. A chemical name alone does not specify a filler’s particle size, surface treatment or performance in a coating.
Calibration (also known as: instrument calibration)
Operation that, under specified conditions, establishes relationships between reference-standard values and instrument indications, including their uncertainties, and uses those relationships to obtain measurement results from indications.
Capillary transport (also known as: capillary suction; wicking)
Movement of liquid through narrow connected pores driven partly by capillary pressure and wettability.
Cenosphere (also known as: cenospheres; fly-ash cenospheres)
A predominantly hollow, spherical, mineral particle separated from certain coal-combustion fly ashes; composition and properties vary by source.
Chalking (also known as: paint chalking; surface chalking)
Formation of a removable powdery deposit at a weathered paint surface; its degree is evaluated using a stated comparison method.
Chemical spot resistance
Response of a coating to local contact with a specified chemical for a specified duration and conditions, not general resistance to all chemicals.
Class A surface
An appearance designation for a highly visible surface that must meet the responsible customer’s specified quality criteria. It is not a universal numerical standard; waviness, reflected-image quality and defects require their own agreed assessments.
Cleanability (also known as: ease of soil or stain removal)
Ability to remove defined contaminants from a surface using a specified cleaning procedure; distinct from film wear resistance.
Co-grinding (also known as: co-grind; combined pigment grind)
Dispersing two or more pigments or particulate ingredients together in one grinding step, rather than producing individual pastes under separate conditions.
Coalescence (also known as: film coalescence)
Formation of a more continuous polymer film as dispersed binder particles deform and join during drying.
Coalescent (also known as: film-forming aid)
Additive used in some dispersion coatings to assist polymer film formation during drying.
Coating film (also known as: coat; dry coating film)
A continuous layer left by application of coating material to a substrate, with performance that depends on film thickness, continuity and cure.
Coating flaking (also known as: flaking; paint scaling)
Detachment of paint in discrete flakes from an exposed coating surface, rated using a defined visual reference.
Coating flexibility (also known as: mandrel-bend flexibility; flexibility by bend)
Ability of a coating on a specified flexible substrate to withstand bending without the failure mode defined by the chosen bend test.
Coating holiday (also known as: holiday; coating discontinuity)
A local breach or gap in an insulating protective coating that can allow electrical detection of the underlying conductive substrate.
Coating material (also known as: paint or coating formulation; coating product)
A liquid, paste or powder formulation applied to a substrate to form a functional surface layer after its applicable drying, fusion or cure process.
Coating pinhole (also known as: pinhole defect)
A small local opening through a coating film that may expose the substrate. Inspection method depends on coating thickness and substrate.
Coating system (also known as: multilayer coating system)
The complete sequence of one or more coating layers applied as a defined protective or decorative construction; individual layer results need not establish system performance.
Coefficient of friction (also known as: COF; static and kinetic friction coefficient)
Ratio of frictional force to normal force for a defined pair of surfaces and state of motion. Contact materials and method must be reported.
Coefficient of linear thermal expansion (also known as: CTE; linear expansion coefficient)
The fractional change in a material's length per unit temperature change. A mean coefficient is calculated as the length change divided by a stated reference length and temperature interval; an instantaneous coefficient uses the local length–temperature slope. State the temperature range and method.
Cohesive failure (also known as: cohesive fracture)
Fracture within one material layer, rather than separation strictly at an interface.
Cold crushing strength (also known as: CCS; ambient refractory crushing strength)
Compressive strength of a refractory test specimen at room temperature, which is not its allowable load under hot service conditions.
Color difference (also known as: colour difference; Delta E)
Numerical separation between instrumentally measured color coordinates with a stated color space and formula. Gloss and texture can affect visual acceptance independently.
Compatibilizer (also known as: compatibilising additive)
Additive intended to improve interaction or morphology between phases in an otherwise poorly compatible mixture.
Completion fluid
A fluid used during operations that prepare a well for production, selected to control the well while limiting damage to the formation and completion equipment. Clean brines are common examples. Required density, chemical compatibility and contamination control are service-specific; suitability as a drilling fluid does not automatically establish suitability for completion service.
Compression set (also known as: permanent compression set)
Residual deformation of a rubber specimen after controlled prolonged compression and recovery, expressed using a prescribed test basis and conditioning history.
Compression-deflection response (also known as: compressive load-deflection response)
Relationship between applied compressive load and specimen deformation under a stated test geometry, speed and conditioning history; rubber standards do not validate every foam or multilayer pad.
Compressive strength (also known as: compression strength)
Maximum compressive stress sustained by a specified test specimen under a defined loading procedure; compare only like specimen shapes and curing histories.
Concrete creep (also known as: creep in concrete)
Time-dependent strain in concrete under sustained load, distinguished from shrinkage measured without applied sustained stress.
Condensation (also known as: moisture condensation)
Conversion of water vapor to liquid when local thermal and humidity conditions allow it.
Conditioning of plastic specimens (also known as: plastic specimen conditioning)
Holding plastic test specimens at stated temperature, humidity and time before testing so results can be meaningfully compared.
Confirmation run
A fresh execution of a previously selected experimental setting to compare a new response with the model prediction. Repeated readings from one specimen are not independent process runs, and local confirmation does not establish a whole operating window.
Confounding (also known as: confounded effects; aliasing in designed experiments)
A situation in which a study design or treatment assignment makes two or more effects inseparable from the observed data, so the individual contribution cannot be identified without additional assumptions or runs.
Contact angle (also known as: wetting angle)
Angle between the solid–liquid and liquid–gas interfaces at their three-phase contact line, conventionally measured through the liquid, using an identified liquid, surface condition and procedure.
Contrast ratio (also known as: hiding contrast ratio)
A reflectance-based comparison of a coating over contrasting reference backgrounds at a defined film build, used to quantify optical hiding; it is not a measurement of near-infrared solar reflectance.
Control sample (also known as: control formulation; reference control)
Specimen or formulation tested as the comparison baseline while other test variables are deliberately changed.
Controlled flocculation
Deliberate formation of a weak, reversible particle network using suitable additives. The network can reduce settling or sagging while breaking down under shear, but its effects on gloss, color and flow depend on the formulation.
Copper-clad laminate (also known as: CCL)
Insulating laminate carrying one or more copper-foil layers and used as a basis for printed circuit boards.
Corrosion creep from scribe (also known as: scribe creep; corrosion undercutting)
Spread of corrosion-associated coating failure away from an intentional cut in a coated test panel, evaluated after a defined exposure.
Corrosion inhibitor
A substance that reduces corrosion through chemical or electrochemical action in a specified environment. A coating’s physical barrier effect is a different mechanism and does not by itself demonstrate active inhibition.
Coverage factor
Multiplier applied to a combined standard uncertainty to obtain an expanded uncertainty. A stated factor alone does not establish a confidence level without the associated distribution and evaluation assumptions.
Cradle-to-gate assessment
A partial life-cycle assessment covering raw-material acquisition and production up to the stated factory gate. It excludes subsequent use and end of life, so its result must not be compared directly with a differently bounded full-life-cycle result.
Cradle-to-grave assessment
An assessment extending from raw-material acquisition through production, distribution and use to end-of-life treatment, within declared boundaries and assumptions. A lighter product is not automatically lower-impact across these stages.
Critical pigment volume concentration (also known as: CPVC)
Formulation-dependent pigment volume concentration at which binder is just sufficient to wet the particles and fill the interparticle spaces. Above this transition, insufficient binder can leave voids in the coating.
Cross-cut adhesion test (also known as: cross-cut test; cross-hatch test)
A coating classification test assessing resistance to separation after a specified lattice is cut through the film to the substrate. Cutting, removal and rating procedures depend on the named method; the classification is not a direct bond-strength measurement.
Cryogenic insulation
Insulation designed for very low service temperatures, requiring evaluation of heat transfer, material integrity and environmental conditions.
Curing (also known as: cure; crosslinking when relevant)
Chemical conversion of a polymer or prepolymer toward a higher-molar-mass or network structure, developing the intended material properties. Solvent loss, physical aging and crystallization alone should not be described as chemical cure.
Cycles per mil
A thickness-normalized test result obtained by dividing a cycle count by coating thickness expressed in mils. One mil is 25.4 micrometres; the failure definition and measured film thickness remain essential to interpretation.
D
D10 (also known as: 10th percentile particle size)
Particle size below which 10 percent of the measured size distribution lies on its stated weighting basis.
D50 (also known as: median particle size; median diameter)
Particle size dividing a stated cumulative distribution into two equal halves; it does not describe the distribution tails.
D90 (also known as: 90th percentile particle size)
Particle size below which 90 percent of a specified cumulative distribution lies under its stated basis.
D95 (also known as: Dv95 when volume based)
Particle diameter below which 95% of a stated cumulative size distribution lies. The distribution basis and method must be specified; a volume-based Dv95 is not a maximum particle size.
Damping ratio (also known as: Modal damping ratio)
A dimensionless measure comparing viscous damping with the critical damping of a specified vibration mode or equivalent oscillator. It characterizes how rapidly free vibration decays within that model. It is not automatically interchangeable with a mechanical loss factor; the damping model, frequency and extraction method must be stated.
Deflocculation (also known as: peptization; de-flocculation)
Disruption of flocs or aggregates to restore a more stable dispersion of particles in a continuous phase.
Defoamer (also known as: antifoam additive)
An additive used to destabilize foam at a liquid surface; effective performance depends on controlled incompatibility, incorporation and dosage.
Degree of conversion (also known as: DC)
The fraction of specified reactive groups consumed relative to their initial amount, commonly expressed as a percentage. In infrared analysis of curing acrylate or methacrylate resins, it can be estimated from the decrease in a reactive-bond absorption signal using a validated reference or calibration. The result describes the sampled material and method; it does not by itself prove uniform cure throughout a coating.
Degree of crystallinity
The fraction of a polymer sample assigned to crystalline material under a stated measurement model. It may be expressed by mass or volume; the technique, reference values and thermal history must accompany the result.
Density (also known as: mass density; ρ)
Mass per unit volume for a specified material state; the volume basis and measurement temperature must be identified.
Dew point (also known as: dew-point temperature)
Temperature at which air reaches saturation with water vapor under its existing vapor content and pressure.
Dewetting
Retraction or breakup of a liquid coating after it has spread across a substrate, leaving locally thin or uncovered regions. Initial wet coverage therefore does not establish film stability; contamination and the complete formulation can influence the result.
Differential scanning calorimetry (also known as: DSC)
A thermal-analysis technique that records the difference in heat flow between a sample and a reference during a specified temperature program.
Dispersibility (also known as: ease of dispersion)
The ability of a powder or particulate material to distribute through a specified medium under stated mixing conditions.
Dissipation factor (also known as: dielectric loss tangent; Df; tan δ)
Electrical dielectric-loss metric that depends on frequency, temperature and specimen conditions; distinct from relative permittivity.
Drilling fluid (also known as: drilling mud)
Circulating well-construction fluid used for functions including cuttings transport, pressure management and borehole conditioning.
Drilling-fluid filtration (also known as: drilling mud filtration; fluid loss)
The movement of a liquid filtrate out of drilling fluid through a test medium under specified pressure, time and temperature conditions; results depend on the filter cake and method.
Dry-film thickness (also known as: DFT; dry paint thickness)
Thickness of a coating after the defined drying or curing process, measured using an applicable method.
Drying shrinkage (also known as: moisture shrinkage; drying contraction)
Dimensional contraction caused by moisture loss as a cementitious material dries; report age, conditioning, geometry and measurement method.
Durometer indentation hardness (also known as: durometer hardness; Shore hardness)
Resistance indexed by the depth of penetration of a specified indenter under defined conditions; results from different hardness methods are not interchangeable.
Dynamic surface tension
Surface tension measured at a specified age of a newly formed liquid interface, before or during equilibration of surface-active components. It is relevant to rapidly created surfaces and must be distinguished from an equilibrium value.
E
Elastic modulus (also known as: modulus of elasticity; Young’s modulus when uniaxial)
A measure relating stress to elastic strain in a specified loading mode. Young’s modulus describes the uniaxial tensile or compressive response; shear and bulk moduli describe different responses and are not interchangeable with it.
Electrostatic stabilization
Resistance to aggregation arising from repulsion between similarly charged particles and their surrounding electrical double layers. Changes in ionic strength, ion valency or surface charge can weaken this stabilization.
Elongation at break
The tensile extension of a specimen at rupture relative to its original gauge length, usually expressed as a percentage. It describes deformation at failure, not the stress required to break the specimen.
Energy-dispersive X-ray spectroscopy (also known as: EDS; EDX)
An analytical technique that uses characteristic X-rays from an electron-excited specimen to investigate elemental composition. It can help distinguish a particle from its surroundings, but an elemental signal does not by itself identify a particular covalent linkage.
Epoxy resin
A resin containing reactive epoxide groups that can form a cured polymer network through reaction with a suitable hardener or catalytic curing route. The uncured resin, mixed formulation and cured epoxy are distinct material states.
Equal-volume replacement (also known as: volume-for-volume substitution)
A formulation comparison in which a defined volume of one ingredient is removed and an equal material volume of another is added, usually changing mass when their densities differ; it is not equal-mass replacement.
Exothermic epoxy cure (also known as: epoxy exotherm)
A resin-hardener curing reaction that releases heat; the temperature rise depends on batch size, geometry, initial conditions and heat removal.
Experimental unit (also known as: independent experimental unit)
The smallest material item or batch independently assigned a treatment in an experiment; several readings on one treated item are not automatically independent replicates.
Extender (also known as: extender pigment)
A particulate ingredient used with the main pigment or binder to adjust volume, texture, cost or specified coating properties.
Extrusion (also known as: extrusion processing)
Manufacturing process in which material is conveyed and shaped continuously through a die.
F
Fairing compound (also known as: fairing mixture)
A material used to fill surface irregularities and form a smooth contour before finishing. In epoxy systems, fairing formulations commonly prioritize low weight and sandability; suitability for fairing does not establish suitability for structural bonding.
Fillet (also known as: epoxy fillet (for epoxy adhesives))
In adhesive joining, a curved bead of thickened adhesive formed along an internal corner between joined parts. It increases the available bonding area and can brace the joint, but its geometry, adhesion and cured material properties must suit the intended load.
Film formation (also known as: coating film formation)
The transformation of an applied liquid coating or molten powder coating into a solid continuous film through drying, coalescence, cooling and/or chemical curing as relevant.
Fineness of grind (also known as: fineness of dispersion; grind fineness)
A gauge-based evaluation of the largest visible pigment agglomerates or particles remaining in a pigment–vehicle dispersion; it does not establish the complete particle-size distribution.
Finger-flow length
The distance a molding material fills a specified narrow cavity under recorded processing conditions. It depends on cavity geometry and the endpoint rule and is not a melt mass-flow rate or geometry-independent material property.
Flexural modulus
A measure of stiffness derived from the stress–strain response in a bending test. Report the method, specimen geometry and calculation convention; it is not interchangeable with tensile modulus or flexural strength.
Flexural strength (also known as: bending strength; strength in flexure)
Maximum flexural stress sustained during the specified bending test; the relevant maximum may correspond to rupture or a yield point. It is not automatically tensile strength.
Floating of pigments (also known as: pigment floating)
Separation of differently mobile pigments through a coating film so that their proportions at the surface differ from those within the film. This can change the visible color and is distinct from uniform settling of the entire pigment mixture.
Flocculation (also known as: floc formation)
Formation of loose aggregates of dispersed particles through weak interactions; the precise sense depends on whether colloid or polymer terminology is used.
Flow rate
The amount of fluid passing a specified location per unit time. Volumetric flow rate uses volume per time, while mass flow rate uses mass per time; conversion requires fluid density under the stated conditions. Flow rate is not viscosity or shear rate.
Fluid structure interaction (also known as: FSI)
Interaction between fluid flow and a movable or deformable structure. Fluid loads can alter structural response, and structural motion may in turn affect the flow. A lower reconstructed fluid load alone does not establish greater structural damage resistance.
Fluidization
In gas-fluidized powder handling, a state in which upward gas flow mobilizes a bed of powder so that it behaves more like a fluid. In powder handling, insufficient or excessive fluidization can disturb delivery; suitable conditions depend on the material and equipment.
Fractional survival (also known as: survival fraction)
The proportion of an initial particle population remaining intact after a specified pressure or processing challenge. The reporting basis, such as particle volume or particle count, and the test conditions must be stated.
Fracture toughness (also known as: fracture resistance)
Resistance of a material or joint to crack initiation or growth under a defined crack geometry and loading mode.
Fresh mortar yield
Volume of mixed fresh mortar obtained from a specified dry-product quantity under stated mixing conditions. Conversion to area coverage requires layer thickness and a declared allowance for application losses.
Functional filler (also known as: functional fillers)
A particulate ingredient selected to affect one or more formulation properties beyond merely increasing volume or reducing cost.
Functional unit
The quantified function used as the basis of a product environmental assessment, including the amount of service, its duration and required quality. Competing products need an equivalent function before their inventories can support a meaningful comparison.
G
Glass fiber (also known as: glass fibre)
Glass in an elongated filament form, used as reinforcement in materials such as polymer composites. Reinforcement may be continuous, chopped, woven or arranged in mats; glass composition, fiber length, orientation and surface sizing must be specified for meaningful comparison.
Glass-transition temperature (also known as: Tg; T_g)
A characteristic temperature assigned within the range over which a polymer changes between glassy and more mobile segmental behavior; the reported value depends on the measurement method, criterion and test conditions.
Gloss (also known as: specular gloss)
Measurement of light reflected around the mirror direction at a specified measuring geometry.
Grafting
Attachment of polymer chains or branches through chemical bonds to another macromolecule or surface. In particle composites, retained polymer after extraction can support an interaction hypothesis, but morphology or retained mass alone is not direct identification of a specific graft bond.
H
Heat flow rate (also known as: heat transfer rate)
Thermal energy transferred per unit time, expressed in watts. Unlike thermal conductivity, it depends on the actual geometry, temperature difference and heat-transfer conditions of the system.
Hegman gauge (also known as: grind gauge; fineness gauge)
A tapered-groove instrument for checking fineness of dispersion by noting where particles or agglomerates protrude or form a visible pattern.
Hiding power (also known as: contrast ratio when method specified)
Ability of a coating to obscure substrate contrast under a specified film thickness and optical test.
Hollow ceramic microsphere (also known as: ceramic hollow sphere; HCM)
A small ceramic particle containing an internal cavity; its chemistry and wall structure must be identified rather than assumed from shape alone.
Hollow glass microsphere (also known as: HGM; hollow glass sphere)
A microscopic particle with a glass shell surrounding an internal void. The generic material class is distinct from any supplier’s branded grade; shell composition, density, size and pressure-survival characteristics require grade-specific evidence.
Hollow thermoplastic microsphere
A small particle with a thermoplastic polymer shell enclosing an internal cavity. Expanded grades serve as lightweight fillers; expandable precursor grades contain a blowing medium and enlarge on heating. Grade and expansion state must be specified.
Hopper bridging (also known as: arching)
A stable arch of bulk particles spanning a hopper outlet and preventing discharge. Mechanical interlocking or cohesive particle interactions can cause it; a hopper shape alone does not guarantee prevention.
Hydrocyclone
Solids-separation device that feeds a liquid suspension into a swirling flow in a conical chamber, dividing material between outlet streams. Separation depends on the suspension and operating conditions; it is not simply screening through an opening.
Hydrophobically modified ASE thickener (also known as: HASE; hydrophobically modified alkali-swellable emulsion)
An ASE-type acrylic thickener with hydrophobic groups that adds associative interactions to pH-dependent swelling.
Hydrophobically modified ethoxylated urethane (also known as: HEUR; urethane associative thickener)
A water-soluble nonionic associative thickener with hydrophilic chains and hydrophobic end groups, used to shape coating flow across shear regimes.
Hydrostatic pressure (also known as: fluid pressure with depth)
Pressure exerted by a static fluid, increasing with depth according to fluid density and gravity.
Hydroxyethyl cellulose (also known as: HEC; hydroxyethylcellulose)
A water-soluble nonionic cellulose ether used to thicken waterborne formulations primarily by polymer hydration and chain interactions.
I
Industrial X-ray computed tomography (also known as: X-ray CT; X-ray computed tomography)
Nondestructive three-dimensional reconstruction of internal features from X-ray projections, sensitive to geometry and attenuation contrast without uniquely determining chemical identity.
Infrared thermography
Imaging that uses detected infrared radiation to estimate and display a surface temperature distribution. Emissivity, reflected radiation, viewing geometry and acquisition timing affect interpretation; the image does not directly measure internal solidification.
Injection molding (also known as: injection moulding)
Process in which molten or reactive material is injected into a closed mold to form a part.
Intercoat adhesion (also known as: adhesion between coats)
Resistance of successive coating layers to interfacial separation. Cross-cut classification tests resistance to separation qualitatively, not absolute adhesion strength.
Internal curing (also known as: internal water curing)
Supply of additional water within a hydrating cementitious mixture from reservoirs that can release it as needed; a sealed hollow particle is not such a reservoir without uptake and release evidence.
Ion chromatography (also known as: IC)
Analytical separation technique used to distinguish and quantify ions in a prepared sample. Extraction or digestion, blanks, calibration, interferences and reporting basis determine what a result says about the original material.
Isostatic crush strength (also known as: isostatic collapse strength)
Pressure-related strength of hollow particles measured under a specified uniform-pressure test and fractional-survival criterion.
K
Kenospheres® (also known as: Kenospheres®)
A branded family of hollow aluminosilicate ceramic microspheres; grade-specific evidence is required before using property claims.
König pendulum hardness
A coating-surface response determined from the damping of a specified pendulum. In the cited oscillation-count method, more oscillations indicate a harder response. Film thickness, conditioning and test age matter; the result is not a direct measure of chemical conversion or complete cure.
L
Latent heat
Energy absorbed or released during a phase transition, reported for a specified mass or amount of material. In a phase-change storage composite, it is distinct from sensible heating and from resistance to heat transfer.
Leaching test (also known as: aqueous extraction test)
A prescribed test exposing material to a defined liquid and contact regime and measuring constituents transferred into the resulting extract; it does not by itself predict release in every field environment.
Let-down stage (also known as: paint letdown; post-grind blending)
A paint manufacturing stage after pigment grinding when binder and additional formulation ingredients are incorporated under controlled mixing, often lower shear.
Leveling (also known as: flow-out)
Ability of a wet coating to smooth application marks before film formation or curing limits its flow.
Loose bulk density (also known as: loose-pour density; untapped bulk density)
Mass of loose powder divided by the volume occupied by the loose powder including interparticle voids, under a stated filling method.
Loss-in-weight feeding (also known as: LIW feeding; gravimetric loss-in-weight feeding)
Controlled dosing that estimates material flow from the decrease in mass of a weighed feeder and adjusts discharge to a target mass rate. Refill periods require a separate control strategy because feeder mass then increases.
Lost circulation
Loss of circulating drilling fluid into the formation rather than its return through the intended circulation path. It is a field-flow outcome, distinct from a laboratory filtrate-volume result.
M
Mass fraction (also known as: weight fraction; mass fraction expressed as weight percent (100w))
Mass of a constituent divided by the total mass on the same defined composition basis, expressed as a fraction or percentage.
Mass-weighted particle-size distribution
A particle-size distribution in which particles contribute according to their mass. Mass-weighted and volume-weighted distributions are equivalent when particle density is uniform across the measured size distribution.
Masterbatch (also known as: concentrate)
Concentrated mixture of an additive or filler in a carrier intended for controlled dilution into a production formulation.
Material lot (also known as: batch; production lot)
A traceable quantity of material produced or supplied under an identified manufacturing history, used for sampling and acceptance decisions.
Matting agent
An additive used to reduce the gloss of a coating. Particulate matting agents commonly create microscopic surface texture that redistributes reflected light. The resulting gloss depends on the additive, formulation, film formation, film thickness and measurement geometry, not simply the mass percentage added.
Measurement uncertainty
A quantified description of the dispersion reasonably associated with a measurement result. It can include statistically evaluated observations and other information such as calibration data; it is not merely the spread of repeated readings.
Mechanical loss factor (also known as: tan delta; tan δ; damping factor)
In linear oscillatory mechanical testing, the ratio of loss modulus to storage modulus. It indicates viscous dissipation relative to elastic energy storage and must be reported with temperature, frequency and test mode. It is not sound transmission loss.
Melt mass-flow rate (also known as: MFR; melt flow index; MFI)
Mass of thermoplastic extruded through a standard die per specified time at prescribed temperature and load; not a direct predictor of production-line shear response.
Melt volume-flow rate (also known as: MVR; volume melt-flow rate)
Volume of thermoplastic passing through a standard die per specified time at prescribed temperature and load; comparison with MFR requires melt density.
Minimum film-forming temperature (also known as: MFFT)
The lowest temperature at which a specified polymer dispersion forms a coherent continuous film under the defined test conditions; it is not the same as the polymer glass-transition temperature.
Mix ratio (also known as: mixing proportion)
Required ratio of components, explicitly expressed by mass or volume and tied to the manufacturer's formulation.
Mode-I critical energy release rate (also known as: G_IC; opening-mode fracture energy)
Energy per unit newly created crack area at the initiation or propagation of an opening-mode crack according to a stated reduction method; distinct from elastic modulus.
Mohs hardness (also known as: Mohs scale)
An ordinal ranking of scratch hardness based on whether one reference mineral scratches another. The scale is not linear and does not measure crushing pressure, toughness or the durability of a finished coating.
Moisture content (also known as: water content)
Water present in a material on a specified wet-mass or dry-mass basis; the reporting basis must be stated.
Molding shrinkage (also known as: moulding shrinkage)
The dimensional reduction of a thermoplastic molding relative to the mold after forming and cooling, measured along specified directions under a named method.
N
Natural frequency
A frequency at which a system can vibrate freely in a particular mode. An undamped natural frequency is defined for the idealized system without damping; the corresponding damped oscillation frequency can differ. Values depend on mass, stiffness and boundary conditions, so a measured modal frequency is not a universal material constant.
Near-infrared radiation (also known as: NIR)
Region of electromagnetic radiation immediately beyond visible red wavelengths, relevant to spectral reflectance and heating.
Normal surface acoustic impedance (also known as: surface impedance; normal acoustic impedance)
Complex ratio of sound pressure to particle velocity at a sample surface under normal-incidence test conditions, generally frequency dependent.
Normal-incidence sound absorption coefficient (also known as: normal sound absorption coefficient; alpha_n)
Fraction of incident acoustic energy absorbed by a sample in an impedance-tube test at a stated frequency and normal incidence.
Nuisance factor (also known as: extraneous factor)
A variable that may affect a measured response but is not the principal treatment under investigation; it should be controlled, blocked, randomized or recorded according to the design.
Number-weighted particle-size distribution
A particle-size distribution in which each measured particle contributes equally, regardless of its size. The reported percentiles refer to the fraction of particles by number.
O
Opacity (also known as: optical opacity)
Extent to which a coating or material blocks transmission or visual recognition of what lies behind it.
Open time (also known as: application open time)
Period after application during which a material can still be joined, adjusted or worked as defined by the test.
P
Packing fraction (also known as: packing efficiency)
Fraction of a powder bed's overall volume occupied by the particles under the selected particle-volume definition.
Paint blistering (also known as: blistering; coating blistering)
Raised local pockets in a coating film assessed by their size and frequency; appearance alone does not prove the underlying cause.
Paint film checking (also known as: checking; paint checking)
A pattern of relatively fine breaks in a dry paint surface that do not penetrate to the substrate; the rating method must be identified.
Paint film cracking (also known as: cracking; paint cracking)
Visible breaks through or within a paint film, evaluated separately from surface chalking and flaking and with defined size/severity criteria.
Particle agglomeration (also known as: agglomeration)
Clustering of particles into larger groups, usually held by comparatively weak interactions; it can alter dispersion and measured particle size.
Particle breakage
Loss of particle integrity during handling, pressure or processing, which can change density and performance.
Particle dispersion (also known as: dispersion of fillers)
The distribution of separate particles throughout a carrier or matrix, as distinct from dissolving the particles.
Particle image velocimetry (also known as: PIV)
Optical method estimating a flow-velocity field from the displacement of visible tracer patterns between images taken at a known time interval. Pressure inferred from that field requires a separate model and assumptions.
Particle loading (also known as: filler loading)
Amount of particulate material added to a formulation, stated on a mass, volume or other explicit basis.
Particle migration
Redistribution of particles within a flowing suspension, potentially changing the local concentration sampled by a rheometer. A measurement affected by migration may no longer represent the initially loaded bulk composition.
Particle-size distribution (also known as: PSD; size distribution)
The proportion of particles across sizes, which must include the measurement method and weighting basis.
Pendulum test value (also known as: PTV)
A slip-resistance reading obtained from the energy loss of a pendulum slider contacting a surface under a defined test. Slider material, direction and wetness or contaminant must accompany the result; it is not interchangeable with every coefficient-of-friction measurement.
Penetrating sealer
A treatment intended to enter a porous substrate rather than function only as a continuous surface film. Penetration depth, uptake, appearance and retained water or stain resistance are separate properties that require evidence for the actual substrate and treatment.
Phase change material (also known as: PCM)
Material used to absorb and release thermal energy through a phase transition, commonly melting and solidification. Useful storage depends on reaching the relevant transition range; the term does not imply low thermal conductivity.
Physical drying (by volatile loss)
Loss of volatile components from a coating or compound, which need not imply complete chemical cure.
Physical foaming
Formation of gas cells in a polymer using a physical blowing agent rather than generating the gas by a chemical blowing reaction. In microcellular injection molding, a pressure change can nucleate cells from a polymer–gas solution.
Pigment concentrate (also known as: pigment paste)
A concentrated dispersion of pigment in a liquid vehicle, prepared for subsequent incorporation into a coating or other formulation. It may contain a grinding resin or be binder-free; compatibility and stabilization must be assessed in the final system.
Pigment oil absorption (also known as: oil uptake; oil-absorption value)
Amount of oil needed to wet a specified pigment mass to an endpoint under a named rub-out method. Indicates vehicle demand, but does not directly measure CPVC.
Pigment volume concentration (also known as: PVC; pigment volume concentration (PVC))
Dry volume fraction of pigments and extenders relative to total dry pigment-plus-binder volume in the specified paint model.
Pipe-in-pipe insulation (also known as: PiP insulation)
Insulation situated in the annular space between an inner pipe and an outer pipe. Its architecture and evidence differ from externally applied wet insulation; a scope written for one system must not automatically be transferred to the other.
Plastisol
A dispersion of fine polymer particles, commonly paste-grade PVC, in a liquid plasticizer. Heating promotes gelation and fusion into a continuous plasticized material. The rheology of the unfused dispersion and the properties of the fused product are different stages of evaluation; a well-shaped dispensed bead does not establish final performance.
Polycarbonate/ABS blend (also known as: PC/ABS; PC+ABS; polycarbonate acrylonitrile-butadiene-styrene blend)
A thermoplastic blend of polycarbonate and acrylonitrile-butadiene-styrene polymers; grade-specific formulation determines its impact, heat and processing characteristics.
Polyurethane dispersion (also known as: PUD)
A dispersion of polyurethane-based polymer particles in a continuous liquid medium, commonly water for waterborne coatings. Particle chemistry and film-formation requirements depend on the grade; waterborne supply does not by itself mean that a product is solvent-free or UV-curable.
Porosity (also known as: void fraction)
Fraction of a sample's volume assigned to pores or voids under a stated measurement definition.
Post-consumer recycled material
Material recovered after it has served its intended end use and then processed for use in another product. A claim needs traceable feedstock classification; it is not established by an unspecified recycled-material label.
Post-industrial recycled material
Material recovered from manufacturing rather than from a product’s completed end use. The applicable accounting rules must be stated, particularly for scrap reused within the same process; the label alone does not certify recycled content.
Post-molding shrinkage (also known as: post-moulding shrinkage; post-shrinkage)
Further dimensional change of a molded thermoplastic specimen after removal from its mold, which can include conditioning effects and must be reported separately.
Pot life (also known as: usable mixed life)
Time for which a mixed reactive formulation remains usable under a specified property limit and test condition.
Potting
Filling or encapsulating a component or assembly with a material that occupies surrounding spaces. The formulation and cured state determine its mechanical, electrical and thermal roles; potting does not inherently mean thermal conduction.
Powder caking (also known as: powder agglomeration during storage)
Consolidation of fine powder into persistent lumps during storage or handling, often favored by humidity or pressure and damaging powder flow.
Pozzolanic reaction
A reaction in a moist cementitious environment in which reactive siliceous or aluminosiliceous constituents consume available calcium hydroxide and contribute cementitious reaction products; the presence of a cenosphere alone proves no such activity.
Primer holdout
The extent to which a primed substrate limits or controls uptake of the subsequent coating, supporting the intended film build and appearance. The relevant uptake or finish endpoint must be stated; holdout is not equivalent to primer penetration or adhesion.
Printed circuit board (also known as: PCB)
Layered electronic interconnection structure containing conductive patterns separated by electrically insulating materials.
Product carbon footprint (also known as: GHG footprint; carbon footprint of a product; CFP)
Climate-change impact attributed to a product system, accounting for greenhouse-gas emissions and removals and expressed in carbon-dioxide equivalents per defined functional unit. A partial product carbon footprint covers stated life-cycle stages or processes and uses an appropriate declared unit; system boundaries must be stated.
Product grade (also known as: grade; material grade)
A supplier-designated variant within a material family whose defined properties and limits must be checked in its own documentation.
Production yield (also known as: accepted production yield; manufacturing yield)
The usable output obtained from a defined quantity of production input or total output on a specified mass, count or volume basis; rejects, rework and denominator must be declared.
Pull-off strength (also known as: pull-off adhesion strength)
Maximum specified perpendicular stress resisted by a tested assembly before rupture, with the failure location recorded.
R
Radome
Protective enclosure for an antenna intended to allow the relevant radio-frequency signals to pass with acceptable effects. Suitability depends on the built wall, frequency band, polarization, incidence conditions and antenna arrangement, not filler Dk alone.
Randomized block design (also known as: randomized blocked design)
An experimental arrangement that compares treatments within groups of runs sharing selected nuisance conditions, with a recorded random allocation or order within each block.
Ratholing (also known as: rat holing)
A bulk-powder flow failure in which a channel empties above the outlet while surrounding material remains stationary. Flow can stop when that channel empties even though material remains in the hopper.
Reaction injection molding (also known as: RIM)
A molding process in which reactive liquid components are mixed and introduced into a mold, where chemical reaction forms the polymeric part. Unlike conventional thermoplastic injection molding, it does not rely primarily on melting and cooling an already formed polymer. Mixing, filling and reaction kinetics must be matched to the chosen chemistry.
Reaction-to-fire classification (also known as: Euroclass reaction to fire)
Classification of a construction product based on prescribed response-to-fire evidence and its stated end-use application; it cannot be transferred automatically to every alternative substrate, thickness or layered build-up.
Reclaimed coating powder (also known as: powder reclaim; recovered overspray)
Powder-coating overspray collected for reuse; product identity, contamination, blending fraction and handling history must be controlled.
Redispersibility
The ability of settled material to become distributed again through a formulation under a defined mixing operation. Visible remixing alone does not establish unchanged application behavior or finished-film performance.
Reference flow
The amount of product required to provide the defined functional unit. For an intermediate material whose final use is unknown, an explicitly stated quantity may instead serve as the inventory basis.
Relative permittivity (real part also known as: dielectric constant; Dk)
Permittivity relative to that of vacuum; in a time-varying field it is generally complex. Its real part, often called dielectric constant or Dk, describes the energy-storage response under specified frequency, temperature and material conditions.
Repeatability (also known as: within-condition repeatability)
Closeness of measurement results for the same measurand under repeatability conditions: the same procedure, operator, measuring system, location and operating conditions over a short time interval.
Replicate (also known as: replicate test)
Repeated observation defined by the experimental unit and sampling plan, not simply multiple instrument readings of one specimen.
Reproducibility (also known as: between-condition reproducibility)
Closeness of results across specified changes of operator, laboratory or other reproducibility conditions.
Resin infusion
A composite manufacturing route in which liquid resin flows into a prepared reinforcement arrangement. Adequate resin filling does not prove that suspended particles pass through the reinforcement or reach every intended location.
Resin transfer molding (also known as: RTM)
A composite-molding process in which resin is introduced into a closed mold containing reinforcement. Filling, wetting, unintended voids and cure must be evaluated for the actual resin, reinforcement and geometry.
Rheology
Study of a material's flow and deformation under applied stresses and conditions.
Rock permeability
Measure of how readily a rock transmits fluid through its connected pore system under defined conditions, commonly reported in darcies or millidarcies. A laboratory permeability-recovery percentage is not a direct measure of well productivity.
Rub-up test
A comparative check in which part of a still-wet pigmented coating is rubbed to redistribute pigment locally, then compared with the untreated area. A color difference can indicate pigment separation or inadequate stabilization; it does not identify the cause by itself.
S
Safety data sheet (also known as: SDS)
A structured hazard-communication document for a chemical product, addressing classification, handling, exposure controls and related safety information.
Sag resistance (also known as: anti-sag behavior)
Ability of a freshly applied coating to limit downward movement before it has set or dried.
Salt-spray testing (also known as: salt fog test)
Laboratory corrosion exposure using defined saline mist; test duration alone cannot be converted into service life.
Saturated-surface-dry condition (also known as: SSD condition)
An aggregate moisture state in which the relevant accessible pores are saturated while free liquid is absent from the outside surface, according to a specified material and measurement protocol.
Scanning electron microscopy (also known as: SEM)
An imaging technique using a scanned electron beam to reveal specimen features at high magnification. Fracture-surface images can show particle and matrix morphology, but appearance alone does not identify a specific chemical bond or prove interface strength.
Scratch resistance (also known as: scratch performance)
Resistance to damage caused by a localized sliding or dragging contact under a specified scratch test.
Sealant movement capability (also known as: joint movement capability)
Range of joint opening or closing that an elastomeric sealant can tolerate under its specified test classification, distinct from cure shrinkage.
Sealant slump
Downward deformation of an uncured sealant under its own weight under specified test conditions. Excessive slump in a vertical joint can distort the bead or reduce its thickness. It is not a measure of cured movement capability.
Sedimentation
The settling of dispersed particles under gravity, producing a concentration difference or sediment in a liquid formulation. Its extent and reversibility depend on the particle population and the surrounding formulation.
Shale shaker
Vibrating-screen device used to separate larger drilled solids from drilling fluid while allowing liquid and sufficiently small particles to pass. Screen identity and actual fluid conditions govern separation performance.
Shear history (also known as: processing shear exposure)
Sequence of shear rates, stresses and durations experienced by a material before measurement or use.
Shear rate (also known as: rate of shear)
Rate of relative deformation between adjacent layers of material, usually expressed in reciprocal seconds.
Shear stress (also known as: shearing stress)
Tangential force per unit area tending to deform a material in shear.
Shear thinning (also known as: pseudoplastic behavior)
Decrease in apparent viscosity with increasing shear rate over a defined range and measurement history.
Sheet molding compound (also known as: SMC)
A prepared, sheet-form fiber-reinforced molding material, commonly based on a thermosetting resin, that is shaped and cured by compression molding. The sheet’s composition and delivered reinforcement content govern its properties.
Silane coupling agent
An organosilicon compound used to modify an interface between inorganic and organic materials. Typical coupling silanes combine hydrolysable groups, which can form bonds with suitable hydroxylated inorganic surfaces, with an organic group selected for interaction or reaction with the polymer. Effectiveness depends on substrate chemistry, treatment conditions and polymer compatibility.
Skeletal density (also known as: gas-pycnometric density when method specified)
Mass divided by the volume of solid material plus pores inaccessible to the measuring fluid, excluding accessible pores and spaces between particles. A sealed hollow cavity therefore contributes to the displaced volume in an appropriate gas-pycnometry measurement.
Skiving
Trimming or shaving material to a required thickness or profile. In a sealant application, the quality of a trimmed bead is a separate observation from dispensing flow and resistance to sag.
Slump of fresh concrete (also known as: concrete slump)
Vertical subsidence of freshly mixed concrete after lifting a standard cone, used to characterize consistency rather than directly certify strength.
Soda-lime-borosilicate glass
A glass composition family containing silica, boron oxide and modifiers such as sodium and calcium oxides, used for hollow glass microspheres.
Solar reflectance (also known as: SR; solar albedo; total solar reflectance; TSR)
Fraction of incident solar radiation reflected by a specified surface or system, integrated using the stated solar spectrum and measurement geometry. It is also reported as total solar reflectance (TSR) on that basis; it is not visible whiteness or solar reflectance index.
Solar reflectance index (also known as: SRI)
Calculated index comparing the steady-state temperature of a horizontal or low-sloped opaque surface with standard black and white reference surfaces under prescribed conditions, using measured solar reflectance and thermal emittance.
Solar spectrum
The distribution of radiation from the Sun across wavelengths. Reflectance measured at individual wavelengths must be weighted using the stated solar spectrum to obtain an integrated solar-reflectance value; a visible color or a single wavelength does not represent the whole spectrum.
Solid ceramic microsphere
A small, approximately spherical ceramic particle without the intentionally hollow interior characteristic of hollow microspheres. Composition and mechanical properties depend on the grade; solidity alone does not establish coating durability.
Solids content (also known as: nonvolatile content; solids fraction)
Proportion of a formulation that remains as defined residue after a specified method; dry and wet bases must not be confused.
Sorptivity (also known as: capillary absorption rate)
A parameter describing the rate of capillary water uptake in a defined unsaturated porous specimen and test configuration.
Sound absorption (also known as: acoustic absorption)
Conversion or dissipation of incident acoustic energy within a specified sample or assembly under stated incidence and frequency conditions; it does not establish wall transmission loss.
Sound transmission loss (also known as: sound reduction index; airborne sound insulation)
Frequency-dependent reduction of transmitted airborne sound through a specified element under a defined measurement configuration, distinct from surface sound absorption.
Specific gravity (also known as: relative density)
Ratio of a material density to a reference density at identified temperatures; the result is dimensionless.
Specific heat capacity (also known as: heat capacity per mass; c_p at constant pressure; c_v at constant volume)
Heat capacity per unit mass, expressed in J/(kg·K), under stated thermodynamic conditions. The constant-pressure value is denoted c_p and the constant-volume value c_v; the basis and temperature must accompany a reported value.
Specific modulus
A specified elastic modulus divided by material density. The loading mode must be retained: specific flexural and specific compressive modulus are different comparisons, not interchangeable measures of overall performance.
Specification limit
A stated boundary against which a defined test result or property is accepted or rejected under an agreed procedure.
Spectral reflectance (also known as: wavelength-resolved reflectance)
Fraction of incident radiation reflected at each specified wavelength, with a stated measurement geometry.
Split-post dielectric resonator (also known as: SPDR)
Microwave resonator method used to determine relative permittivity and dielectric loss of a prepared dielectric substrate. The frequency-specific fixture, specimen thickness, foil removal and measurement direction must remain attached to the result.
Steric stabilization
Resistance to particle aggregation provided by adsorbed polymer layers that remain compatible with the surrounding liquid. Bringing the layers together is energetically unfavorable. Effective anchoring and adequate chain solvation are necessary; adsorption alone does not guarantee stability.
Storage modulus
Elastic component of a material’s oscillatory mechanical response, describing the in-phase stress relative to applied strain. Report the loading mode, frequency, temperature and strain range; it is not a service-temperature rating.
Stress relaxation
A decrease in stress with time while strain is held fixed. It differs from creep, which concerns time-dependent deformation under sustained loading; material age, temperature and moisture can affect the response.
Surface temperature (also known as: skin temperature)
Temperature at the outermost measured surface, not necessarily the air or internal specimen temperature.
Surface tension
Work required to create unit area of a liquid interface, equivalently force per unit length, commonly reported in mN/m. The value depends on the liquid, temperature and interface condition; a lower value alone does not prove adequate substrate wetting.
Surface treatment
A modification of particle surfaces intended to influence handling or their interaction with the surrounding matrix.
Syntactic foam (also known as: hollow-sphere composite)
Composite in which hollow particles are dispersed within a continuous matrix to create controlled internal void volume.
T
Tack-free time (also known as: tack-free drying time)
Time after coating application at which the film meets an explicitly specified non-tacky surface criterion under named temperature, humidity and test conditions; it is not necessarily fully cured.
Tapped bulk density (also known as: tapped density)
Mass of powder per the final volume occupied by the powder after a defined tapping procedure that changes interparticle packing.
Technical data sheet (also known as: TDS; product data sheet)
A supplier document describing a named product and its reported properties, test methods and revision, which is not automatically a purchase specification.
Tensile strength
Maximum tensile stress reached in a defined tensile test, using the stress and strength convention of the stated method; it is not necessarily the tensile stress at break.
Thermal bridge
A region of a building envelope where material changes, thickness changes or junction geometry alter the otherwise more uniform thermal resistance. It affects local heat flow and surface temperature; adding a thin coating does not by itself demonstrate that the bridge has been eliminated.
Thermal conductivity (also known as: k; λ)
Property quantifying conductive heat flow through a material for an imposed temperature gradient, expressed in W/(m·K).
Thermal contact resistance (also known as: interfacial thermal resistance; contact resistance)
Temperature difference across a contacting interface divided by the heat-flow rate, expressed in K/W, or by heat flux for the area-normalized value in m²·K/W. The chosen basis, contact pressure, surface condition and measurement arrangement must be stated.
Thermal cycling
Repeated changes between specified temperatures during service or testing. Heating and cooling can generate stresses where components expand differently. A meaningful comparison states the temperature limits, rates, dwell times and number of cycles rather than reporting only that cycling occurred.
Thermal diffusivity (also known as: α)
Ratio of thermal conductivity to volumetric heat capacity, indicating the pace of temperature response in conduction.
Thermal effusivity
A measure of a material’s transient thermal response at its surface, given by the square root of the product of thermal conductivity, density and specific heat capacity, b = √(kρc). Its SI unit is J/(m²·K·√s). It is not thermal resistance or proof of perceived comfort.
Thermal emittance (also known as: thermal emissivity; TE)
Ratio describing how effectively a surface emits thermal radiation relative to an ideal blackbody at the same temperature.
Thermal interface material (also known as: TIM)
A material placed between heat-transferring surfaces to improve thermal contact, particularly by replacing interfacial air gaps. Forms include pads, pastes, phase-change materials and thermally conductive gap fillers. Thermal performance depends on conductivity, contact quality, coverage and thickness. A material described only as a gap filler is not necessarily designed for conductive heat transfer.
Thermal resistance (also known as: R; R-value when area-normalized)
Temperature difference across a specified thermal path divided by heat-flow rate, expressed in K/W. An area-normalized resistance divides temperature difference by heat flux and is expressed in m²·K/W; building R-values commonly use this latter basis. Geometry and boundary conditions must be stated.
Thermal transmittance (also known as: U-value)
Steady-state heat flow through a building element divided by its area and the temperature difference between the environments on its two sides. Expressed in W/(m²·K), it describes the complete specified construction and boundary conditions, not simply the conductivity of one coating.
Thermally expandable microsphere
A particle with a heat-softening polymer shell enclosing a volatile expansion medium. Heating can expand the shell as internal pressure increases; this architecture differs from a pre-existing rigid hollow glass sphere.
Thermesthesiometer
An instrument used to simulate a defined thermal-contact interaction and estimate a contact-related temperature response. Its reading is not automatically the coating surface temperature, measured human skin temperature or a safety approval.
Thermogravimetric analysis (also known as: TGA; thermogravimetry)
A technique that records sample mass as temperature or time changes under a controlled atmosphere; weight losses require interpretation before being assigned to components.
Thermomechanical analysis (also known as: TMA)
Technique measuring dimensional change of a specimen under a defined mechanical load as temperature or time is controlled. Thermal expansion and transition results depend on measurement direction, load and temperature programme.
Thermoplastic (also known as: thermoplastic polymer)
Polymer that can generally soften and flow upon heating without requiring a new crosslinking reaction.
Thermoset (also known as: cured thermosetting polymer)
Polymer network that becomes irreversibly set by curing and does not melt and flow as an ordinary thermoplastic.
Thixotropy (also known as: thixotropic behavior)
Time-dependent reduction and recovery of material structure and viscosity under changes in shear history.
Titanium dioxide (also known as: TiO2; TiO₂)
High-refractive-index white pigment commonly used to scatter visible light and provide hiding in coatings.
Transmission haze
Fraction of transmitted light scattered outside the angular limit specified by the optical test, distinguished from narrow-angle clarity and reflection haze.
True particle density (also known as: particle density (with specified method and volume convention))
Particle mass divided by the particle volume defined by the measurement method. In hollow-microsphere supplier data, this commonly includes a sealed internal cavity but excludes spaces between particles; it must not be confused with the density of the solid shell material.
Two-component system (also known as: two-part system; 2K system)
A reactive formulation supplied as two separate components that are combined in the specified proportion before application. Mixing initiates or enables curing; the required mass or volume ratio and usable working time depend on the particular system.
Typical property (also known as: typical value)
A descriptive result intended to characterize usual material behavior, not necessarily an enforceable acceptance limit.
U
Ultraviolet curing (also known as: UV curing)
A curing route driven by ultraviolet-initiated reactions after adequate radiation reaches the reactive material.
Unintended void
An unplanned gas pocket, unfilled region or separation in a material or component. In a syntactic material it must be distinguished from the deliberately enclosed interiors of hollow particles when interpreting density, microscopy and performance.
Urethane acrylate resin (also known as: urethane-acrylate)
A urethane-based resin or oligomer carrying reactive acrylate functionality. Molecular structure and functionality vary between grades, so cure route, processing window and cured properties must be taken from the identified formulation rather than inferred from the family name.
V
Vacuum
A gas-pressure condition below the surrounding atmospheric pressure. For quantitative comparison, report absolute pressure and its unit, together with relevant gas composition and temperature. A vacuum regime identifies a pressure range or associated gas-flow behavior; pumpdown history is not interchangeable with the pressure present during a cold insulation measurement.
Viscosity (also known as: dynamic viscosity; shear viscosity)
Measure relating shear stress to the rate of shear deformation for a specified material and test condition.
VOC content (also known as: volatile organic compound content)
A measured or calculated amount of qualifying volatile organic compounds in a coating on an explicitly stated mass or volume basis; regulatory exclusions depend on jurisdiction.
Volatile content (also known as: volatile matter; volatile fraction)
The fraction of a coating lost under an identified heating method, which cannot automatically be treated as VOC content.
Volume fraction (also known as: volume fraction expressed as volume percent (100φ))
Volume of a constituent divided by a stated reference volume. In the IUPAC mixture convention, the denominator is the sum of constituent volumes before mixing; in composite characterization, a phase volume fraction is commonly referred to the total composite volume. State the material condition, volume basis and treatment of voids. Volume percent is 100 times the volume fraction.
Volume nonvolatile matter (also known as: volume solids; NVV)
The volume of nonvolatile dry coating produced under stated conditions relative to the original liquid coating volume, expressed on a specified measurement or calculation basis.
Volume-weighted particle-size distribution
A particle-size distribution in which particles contribute according to their volume. Larger particles therefore have a greater influence on the distribution than smaller particles.
Volumetric feeding (also known as: volumetric dosing)
Dosing controlled by the volume delivered per unit time. The corresponding mass rate changes if the material's bulk density or filling behaviour changes.
W
Wall slip
Relative motion between a tested material and a rheometer boundary that can make the apparent flow response differ from the bulk material response. Appropriate geometry and method checks are needed; instrument calibration alone does not rule it out.
Warpage (also known as: part distortion)
Departure of a manufactured part from its intended shape after molding, cooling or other processing.
Water absorption (also known as: water uptake)
Quantity of water entering or retained by a material under specified exposure, conditioning and measurement conditions.
Water desorption (also known as: moisture release)
Release of water previously held by a material when environmental moisture or temperature conditions change; uptake capacity alone does not show how much water is available to the surrounding matrix.
Water flash
A drying stage intended to remove water from an applied waterborne coating before a later operation such as UV curing. Film readiness and subsequent chemical cure are separate acceptance questions.
Water repellency (also known as: hydrophobicity when test specified)
Surface tendency to resist wetting or liquid-water penetration under a specified exposure, not proof of zero vapor permeability.
Water-vapor permeability (also known as: water vapour permeability)
Material coefficient relating water-vapor mass flux to the vapor-pressure gradient under stated temperature and humidity conditions. Permeance additionally depends on specimen thickness; water-vapor transmission rate is the mass transmitted per area and time, not permeability.
Water-vapor transmission rate (also known as: WVTR; WVT rate)
Mass of water vapour transmitted per unit area per unit time under defined test conditions; it is not the same quantity as material permeability.
Waterborne coating (also known as: water-based paint)
Coating in which water is the principal continuous liquid medium; it is not necessarily water soluble.
Wear-through
Removal or damage of a coating to a defined endpoint at which the underlying substrate becomes exposed. Cycles to wear-through describe that endpoint and cannot be substituted for mass loss after a fixed number of cycles.
Well-cement slurry (also known as: cement slurry for wells)
Pumpable cementitious material placed in a well to form a specified sealing and mechanical barrier after setting.
Wet thermal insulation system (also known as: subsea wet insulation; wet insulation)
A subsea thermal insulation configuration designed for service while externally immersed in seawater, qualified as a particular material and installed system rather than by one property alone.
Wet-film thickness (also known as: WFT)
Thickness of a freshly applied liquid coating before drying or curing, measured by an appropriate wet-film method.
Wet-scrub resistance (also known as: scrub resistance)
Resistance of a coating to film wear from repeated wet scrubbing under a specified accelerated test.
Wetting (also known as: surface wetting)
Spreading or maintaining liquid contact on a solid surface; it depends on interfacial properties.
Wood polymer composite (also known as: WPC)
A composite combining a polymer matrix with wood-derived material such as wood flour. Its geometry, processing history and formulation affect performance; easier drilling does not establish fastener retention.
Y
Yield stress (also known as: yield value)
Estimated stress threshold associated with sustained flow in a structured material under the chosen model or method.